Happy Thanksgiving from Bailiff Enterprises! Our office and plant will be closed Thursday, November 26 and Friday, November 27, 2026. We reopen Monday, November 30.

Fittings & options

Polypropylene Tank Fittings & Options

Polypropylene fittings match the chemical resistance and 200°F rating of your polypropylene tank. We install every fitting and accessory at our Willis, Texas plant, so your tank arrives ready to connect.

  • Welded PP couplings & flanges
  • PP bulkheads & valves
  • Level, leak & heat options

Downloads

Fittings & Options Spec Sheets

Download spec sheets for the fittings and options we install on polypropylene storage tanks at our Willis, Texas plant. Each sheet covers materials, sizes and how the fitting is installed. Email dmiller@plasticstoragetanks.com if you need a sheet that isn't listed.

Pipe connection fittings

Valves & piping

Vents & lids

Connections

Welded & Bulkhead Fittings

Welded fittings are fused to the tank wall in matching polypropylene for a leak-free, chemical-resistant connection.

Polypropylene welded threaded coupling on a plastic tank
1″ – 4″ FNPT

Welded Couplings

Polypropylene couplings welded into the tank wall, with a female NPT thread for your piping.

Gusseted polypropylene welded flange on a tank
1″ – 10″ ANSI 150#

Welded Flanges

Gusseted polypropylene flanges welded to the tank with Vanstone rings, drilled to ANSI 150# bolt patterns.

Large bolted welded flange on a plastic storage tank
Up to 10″

Large Outlet Flanges

Large-diameter welded flanges for high-flow outlets and transfer lines.

Polypropylene bulkhead fitting for plastic tanks
½″ – 4″

Polypropylene Bulkheads

The most common tank fitting, always threaded (FIPT). Gaskets in Viton®, EPDM or Buna-N, chosen to match your chemical.

Self-aligning bulkhead for tank domes
2″ – 3″ · Top only

Self-Aligning Bulkheads

Seals on the curved dome of the tank, for top-of-tank connections only.

Sanitary Tri-Clamp adapter
½″ – 4″

Sanitary Tri-Clamps

Quick-disconnect sanitary connections for clean and food-grade service, in polypropylene.

Bolted spool flange fitting

Bolted & Spool Flanges

A bolted flange through the tank wall, an alternative where a welded flange isn’t the right fit.

Valves & vents

Valves, Vents & Fill Lines

Polypropylene bolted ball valve
150 psi · PTFE seats

Polypropylene Ball Valves

Bolted polypropylene ball valves with PTFE seats and locking handles, rated 150 psi.

Screened U-vent for a plastic storage tank
2″ · 3″ · 4″

Screened U-Vents

Every atmospheric tank needs a vent. U-vents keep rain and debris out while the tank breathes.

Diagram of a top fill line on a plastic tank

Top Fill Lines

Fill from ground level through a line that runs up the sidewall and into the top of the tank.

Diagram of a top siphon drain line

Top Drain Lines

Draw liquid from the top of the tank without a sidewall fitting below the liquid level.

Monitoring

Level & Leak Monitoring

Diagram of a reverse float level indicator

Reverse Float Level Indicators

A simple, non-electric gauge: the float rides the liquid and an outside indicator shows the level.

Ultrasonic level transmitter

Ultrasonic Level Sensors

Non-contact ultrasonic level measurement with an optional display and controller.

Interstitial leak detector with strobe alarm
Double wall tanks

Interstitial Leak Detectors

For double wall tanks. A probe between the walls sounds an alarm, flashes a strobe and can signal your PLC.

Thermal

Insulation & Heat Tracing

Spray-foam insulated vertical storage tank
R-6.7 per inch

Spray-Foam Insulation

Closed-cell polyurethane foam sealed with a UV-resistant white mastic. 2″ standard; 3″ and 4″ optional.

Heat trace pads and controller on a plastic tank

Heat Tracing

Heat trace pads and a temperature controller hold your chemical at temperature and prevent freezing.

Installation & safety

Installation & Safety

Tie-down cable layout on a vertical tank
120 mph

Wind & Seismic Tie-Downs

Galvanized cable tie-down systems for vertical tanks under 5,000 gallons, rated for 120 mph winds.

Molded tie-down lug with cable and anchor

Molded Tie-Down Lugs

Lifting and tie-down lugs are molded into the tank for secure anchoring.

Safety note

Oxidizing Chemicals

We do not install welded flanges in the sidewalls of tanks storing nitric acid, sodium hypochlorite, sulfuric acid or other oxidizers. We will recommend the right fitting for your chemical.

Match Fittings to Your Chemical

Gasket and fitting materials depend on what you store. Check the ratings, then pick your tank.

★ Tank Wizard